Question # 1 Refer to the exhibit, which shows a Branch1 configuration and routing table.
In the SD-WAN implicit rule, you do not want the traffic load balance for the overlay
interface when all members are available.
In this scenario, which configuration change will meet this requirement? A. Change the load-balance-mode to source-ip-based.B. Create a new static route with the internet sdwan-zone onlyC. Configure the cost in each overlay member to 10.D. Configure the priority in each overlay member to 10.
Click for Answer
D. Configure the priority in each overlay member to 10.
Answer Description Explanation: The default load balancing mode for the SD-WAN implicit rule is source IP
based. This means that traffic will be load balanced evenly between the overlay members,
regardless of the member's priority.
To prevent traffic from being load balanced, you can configure the priority of each overlay
member to 10. This will make the member ineligible for load balancing.
The other options are not correct. Changing the load balancing mode to source-IP based
will still result in traffic being load balanced. Creating a new static route with the internet
sdwan-zone only will not affect the load balancing of the overlay interface. Configuring the
cost in each overlay member to 10 will also not affect the load balancing, as the cost is only
used when the implicit rule cannot find a match for the destination IP address.
Question # 2 You are migrating the branches of a customer to FortiGate devices. They require
independent routing tables on the LAN side of the network.
After reviewing the design, you notice the firewall will have many BGP sessions as you
have two data centers (DC) and two ISPs per DC while each branch is using at least 10
internal segments.
Based on this scenario, what would you suggest as the more efficient solution, considering
that in the future the number of internal segments, DCs or internet links per DC will
increase? A. No change in design is needed as even small FortiGate devices have a large memory
capacity.B. Acquire a FortiGate model with more capacity, considering the next 5 years growth.C. Implement network-id, neighbor-group and increase the advertisement-intervalD. Redesign the SD-WAN deployment to only use a single VPN tunnel and segment traffic
using VRFs on BGP
Click for Answer
D. Redesign the SD-WAN deployment to only use a single VPN tunnel and segment traffic
using VRFs on BGP
Answer Description Explanation: Using multiple VPN tunnels and BGP sessions for each internal segment is
not scalable and efficient, especially when the number of segments, DCs or internet links
per DC increases. A better solution is to use a single VPN tunnel per branch and segment
traffic using virtual routing and forwarding (VRF) instances on BGP. This way, each VRF
can have its own routing table and BGP session, while sharing the same VPN tunnel.
Question # 3 You are troubleshooting a FortiMail Cloud service integrated with Office 365 where
outgoing emails are not reaching the recipients' mail What are two possible reasons for this
problem? (Choose two.) A. The FortiMail access control rule to relay from Office 365 servers FQDN is missing.B. The FortiMail DKIM key was not set using the Auto Generation option.C. The FortiMail access control rules to relay from Office 365 servers public IPs are
missing.D. A Mail Flow connector from the Exchange Admin Center has not been set properly to the FortiMail Cloud FQDN.
Click for Answer
A. The FortiMail access control rule to relay from Office 365 servers FQDN is missing.D. A Mail Flow connector from the Exchange Admin Center has not been set properly to the FortiMail Cloud FQDN.
Answer Description Explanation: A. The FortiMail access control rule to relay from Office 365 servers FQDN is
missing.
If the access control rule to relay from Office 365 servers FQDN is missing, then FortiMail
will not be able to send emails to Office 365. This is because the access control rule
specifies which IP addresses or domains are allowed to relay emails through FortiMail.
D. A Mail Flow connector from the Exchange Admin Center has not been set properly to
the FortiMail Cloud FQDN.
If the Mail Flow connector from the Exchange Admin Center is not set properly to the
FortiMail Cloud FQDN, then Office 365 will not be able to send emails to FortiMail. This is
because the Mail Flow connector specifies which SMTP server is used to send emails to
external recipients.
Question # 4 Refer to the exhibit.
FortiManager is configured with the Jinja Script under CLI Templates shown in the exhibit.
Which two statements correctly describe the expected behavior when running this
template? (Choose two.) A. The Jinja template will automatically map the interface with "WAN" role on the managed
FortiGate.B. The template will work if you change the variable format to $(WAN).C. The template will work if you change the variable format to {{ WAN }}.D. The administrator must first manually map the interface for each device with a meta
field.E. The template will fail because this configuration can only be applied with a CLI or TCL
script.
Click for Answer
D. The administrator must first manually map the interface for each device with a meta
field.E. The template will fail because this configuration can only be applied with a CLI or TCL
script.
Answer Description Explanation: D. The administrator must first manually map the interface for each device
with a meta field.
The Jinja template in the exhibit is expecting a meta field calledWANto be set on the
managed FortiGate. This meta field will specify which interface on the FortiGate should be
assigned the "WAN" role. If the meta field is not set, then the template will fail.
E. The template will fail because this configuration can only be applied with a CLI or TCL
script.
The Jinja template in the exhibit is trying to configure the interface role on the managed
FortiGate. This type of configuration can only be applied with a CLI or TCL script. The Jinja
template will fail because it is not a valid CLI or TCL script.
Question # 5 Refer to the exhibit.
You are operating an internal network with multiple OSPF routers on the same LAN
segment. FGT_3 needs to be added to the OSPF network and has the configuration shown
in the exhibit. FGT_3 is not establishing any OSPF connection.
What needs to be changed to the configuration to make sure FGT_3 will establish OSPF
neighbors without affecting the DR/BDR election?
A. Option AB. Option BC. Option CD. Option D
Click for Answer
B. Option B
Answer Description Explanation: The OSPF configuration shown in the exhibit is using the default priority
value of 1 for the interface port1. This means that FGT_3 will participate in the DR/BDR
election process with the other OSPF routers on the same LAN segment. However, this is
not desirable because FGT_3 is a new device that needs to be added to the OSPF network
without affecting the existing DR/BDR election. Therefore, to make sure FGT_3 will
establish OSPF neighbors without affecting the DR/BDR election, the priority value of the
interface port1 should be changed to 0. This will prevent FGT_3 from becoming a DR or
BDR and allow it to form OSPF adjacencies with thecurrent DR and BDR. Option B shows
the correct configuration that changes the priority value to 0. Option A is incorrect because
it does not change the priority value. Option C is incorrect because it changes the network
type to point-to-point, which is not suitable for a LAN segment with multiple OSPF routers.
Option D is incorrect because it changes the area ID to 0.0.0.1, which does not match the
area ID of the other OSPF routers on the same LAN segment.
Question # 6 Refer to the exhibit.
You are deploying a FortiGate 6000F. The device should be directly connected to a switch.
In the future, a new hardware module providing higher speed will be installed in the switch,
and the connection to the FortiGate must be moved to this higher-speed port.
You must ensure that the initial FortiGate interface connected to the switch does not affect
any other port when the new module is installed and the new port speed is defined.
How should the initial connection be made? A. Connect the switch on any interface between ports 21 to 24B. Connect the switch on any interface between ports 25 to 28C. Connect the switch on any interface between ports 1 to 4D. Connect the switch on any interface between ports 5 to 8.
Click for Answer
C. Connect the switch on any interface between ports 1 to 4
Answer Description Explanation: The FortiGate 6000F has 24 1/10/25-Gbps SFP28 data network interfaces (1
to 24). These interfaces are divided into the following interface groups: 1 to 4, 5 to 8, 9 to
12, 13 to 16, 17 to 20, and 21 to 24. The ports 25 to 28 are 40/100-Gbps QSFP28 data
network interfaces.
The initial connection should be made to any interface between ports 1 to 4. This is
because the ports 21 to 24 are part of the same interface group, and changing the speed of
one of these ports will affect the speeds of all of the ports in the group. The ports 5 to 8 are
also part of the same interface group, so they should not be used for the initial connection.
The new hardware module that will be installed in the switch will provide higher speed
ports. When this module is installed, the speed of the ports 21 to 24 will be increased.
However, this will not affect the ports 1 to 4, because they are not part of the same
interface group.
Therefore, the initial connection should be made to any interface between ports 1 to 4, in
order to ensure that the FortiGate interface connected to the switch does not affect any
other port when the new module is installed and the new port speed is defined.
Question # 7 You are deploying a FortiExtender (FEX) on a FortiGate-60F. The FEX will be managed by
the FortiGate. You anticipate high utilization. The requirement is to minimize the overhead
on the device for WAN traffic.
Which action achieves the requirement in this scenario? A. Add a switch between the FortiGate and FEX.B. Enable CAPWAP connectivity between the FortiGate and the FortiExtender.C. Change connectivity between the FortiGate and the FortiExtender to use VLAN ModeD. Add a VLAN under the FEX-WAN interface on the FortiGate.
Click for Answer
C. Change connectivity between the FortiGate and the FortiExtender to use VLAN Mode
Answer Description Explanation: VLAN Mode is a more efficient way to connect a FortiExtender to a FortiGate
than CAPWAP Mode. This is because VLAN Mode does not require the FortiExtender to
send additional control traffic to the FortiGate.
The other options are not correct.
A. Add a switch between the FortiGate and FEX. This will add overhead to the
network, as the switch will need to process the traffic.
B. Enable CAPWAP connectivity between the FortiGate and the FortiExtender.
This will increase the overhead on the FortiGate, as it will need to process
additional control traffic.
D. Add a VLAN under the FEX-WAN interface on the FortiGate. This will not affect
the overhead on the FortiGate.
Question # 8 A customer wants to use the FortiAuthenticator REST API to retrieve an SSO group called
SalesGroup. The following API call is being made with the 'curl' utility:
Which two statements correctly describe the expected behavior of the FortiAuthenticator
REST API? (Choose two.) A. Only users with the "Full permission" role can access the REST APIB. This API call will fail because it requires that API version 2C. If the REST API web service access key is lost, it cannot be retrieved and must be
changed.D. The syntax is incorrect because the API calls needs the get method.
Click for Answer
B. This API call will fail because it requires that API version 2D. The syntax is incorrect because the API calls needs the get method.
Answer Description Explanation: To retrieve an SSO group called SalesGroup using the FortiAuthenticator
REST API, the following issues need to be fixed in the API call:
The API version should be v2, not v1, as SSO groups are only supported in
version 2 of the REST API.
The HTTP method should be GET, not POST, as GET is used to retrieve
information from the server, while POST is used to create or update information on
the server. Therefore, a correct API call would look like this: curl -X GET -H
“Authorization: Bearer ”
Up-to-Date
We always provide up-to-date NSE8_812 exam dumps to our clients. Keep checking website for updates and download.
Excellence
Quality and excellence of our Network Security Expert 8 Written practice questions are above customers expectations. Contact live chat to know more.
Success
Your SUCCESS is assured with the NSE8_812 exam questions of passin1day.com. Just Buy, Prepare and PASS!
Quality
All our braindumps are verified with their correct answers. Download Fortinet Network Security Expert Practice tests in a printable PDF format.
Basic
$80
Any 3 Exams of Your Choice
3 Exams PDF + Online Test Engine
Buy Now
Premium
$100
Any 4 Exams of Your Choice
4 Exams PDF + Online Test Engine
Buy Now
Gold
$125
Any 5 Exams of Your Choice
5 Exams PDF + Online Test Engine
Buy Now
Passin1Day has a big success story in last 12 years with a long list of satisfied customers.
We are UK based company, selling NSE8_812 practice test questions answers. We have a team of 34 people in Research, Writing, QA, Sales, Support and Marketing departments and helping people get success in their life.
We dont have a single unsatisfied Fortinet customer in this time. Our customers are our asset and precious to us more than their money.
NSE8_812 Dumps
We have recently updated Fortinet NSE8_812 dumps study guide. You can use our Fortinet Network Security Expert braindumps and pass your exam in just 24 hours. Our Network Security Expert 8 Written real exam contains latest questions. We are providing Fortinet NSE8_812 dumps with updates for 3 months. You can purchase in advance and start studying. Whenever Fortinet update Network Security Expert 8 Written exam, we also update our file with new questions. Passin1day is here to provide real NSE8_812 exam questions to people who find it difficult to pass exam
Fortinet Network Security Expert can advance your marketability and prove to be a key to differentiating you from those who have no certification and Passin1day is there to help you pass exam with NSE8_812 dumps. Fortinet Certifications demonstrate your competence and make your discerning employers recognize that Network Security Expert 8 Written certified employees are more valuable to their organizations and customers. We have helped thousands of customers so far in achieving their goals. Our excellent comprehensive Fortinet exam dumps will enable you to pass your certification Fortinet Network Security Expert exam in just a single try. Passin1day is offering NSE8_812 braindumps which are accurate and of high-quality verified by the IT professionals. Candidates can instantly download Fortinet Network Security Expert dumps and access them at any device after purchase. Online Network Security Expert 8 Written practice tests are planned and designed to prepare you completely for the real Fortinet exam condition. Free NSE8_812 dumps demos can be available on customer’s demand to check before placing an order.
What Our Customers Say
Jeff Brown
Thanks you so much passin1day.com team for all the help that you have provided me in my Fortinet exam. I will use your dumps for next certification as well.
Mareena Frederick
You guys are awesome. Even 1 day is too much. I prepared my exam in just 3 hours with your NSE8_812 exam dumps and passed it in first attempt :)
Ralph Donald
I am the fully satisfied customer of passin1day.com. I have passed my exam using your Network Security Expert 8 Written braindumps in first attempt. You guys are the secret behind my success ;)
Lilly Solomon
I was so depressed when I get failed in my Cisco exam but thanks GOD you guys exist and helped me in passing my exams. I am nothing without you.